In this article in the next paragraph you might get a bunch of amazing ideas relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't precisely brain surgery, but it does require strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is readily obtainable, the task can move immediately; if you have to open up a wall surface to remove the old tub as well as place the new bath tub, the task is much harder. In either case, the task is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub as well as set in the new one. Make certain you have actually qualified on your own for the work as well as are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed job, it is better to think about using one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This article will certainly help you mount a new bath tub in your shower room if you have currently acquired a brand-new tub and also do not need to change the arrangement of your previous water pipes.
Your tools and also material list should comprise the following:
Planning for the Installment
To start with, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome because of the limited accessibility that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipelines. When the supply pipelines have been gotten rid of, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from transforming throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, put the bath tub in the called for placement. The wood boards are valuable in uniformly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the bath tub till the spirit level reads degree.
To install faucets, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally check the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the tub must wait till the bath tub has been used a minimum of when as this will settle it right into its final position.
Fitting New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin ensuring that the washers remain in area between the faucet and the sink. Protect the faucet in place with the manufacturer offered backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet adapters. The previous type must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split a rigid seal, triggering the water to permeate the wall in between the bath and the tiling, leading to difficulties with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes and cartridges, and also are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealant can break relatively early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that editorial about How to Install a Bathtub through an acquaintance on a different web blog. Enjoyed reading our review? Please share it. Help another person find it. I truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Overflow? Seek assistance.